Why are my steps not working in my motor home?
If so your step will not operate. You might also have a bad magnetic switch in your door, if so again your step won’t operate. Let us know what you find. Most steps run off the engine battery so you can turn off the house and still get in and out of the motor home. You might want to check fuses for the steps.
How does electric step on motor home work?
There is a switch inside the door, one for step out, one for step in. If the step is left out it will also go in when the key is turned in the ignition. I believe it also works on a remote control on my key ring but I don’t remember using it. It’s two years since I used the van because of health.
How can you tell if your step motor is working?
First verify that the magnet in the door and door frame switch are aligned. They should line up when the door is closed. Then check if power is getting to the step motor. Disconnect the power cable from the motor. Then use a multi-meter to check for a DC voltage reading of around 12 volts when the door switch is activated.
What makes the steps extend on an RV?
On Automatic RV steps, the magnetic switch is the one that makes your steps extend when the door opens and ensures that your RV steps retract when the door closes. There is a magnetic switch found on the sides of the door and the door frame. These should be aligned perfectly for the electric steps to automatically retract.
Why are the steps not working in my RV?
Answer: The most obvious source of the problem is that you have inadvertently hit a switch that turns off the automatic steps. For instance, in our RV there is a toggle switch near the entry door that allows us to turn off the automatic steps.
How does an automatic step on an RV work?
Automatic RV Steps Automatic RV steps automatically extend when the door opens and immediately retract on their own as soon as the door closes. This is made possible thanks to the magnetic switch located at the bottom part of the frame and door. They also automatically retract when you start the ignition.
What to do if your step motor is not working?
Start by making sure you have power to the step motor. Then trace the wiring all the way to the battery. You are looking for loose or broken wires, poor continuity, bad grounds, or blown fuses. Do not forget to check for faulty parts or bad connections to the door switch sensor and the on/off switch to the steps.
How to repair an automatic step-RV with Tito?
1 Disconnect the main connector to step and controller unit 2 Remove the bolts securing the controller board (leave wires connected) 3 Replace the controller board with the new one and secure it with the bolts 4 Move each wire from the old controller to the new controller 5 Reconnect the main plug to the step 6 Verify proper step operation
What to do if your steps won’t come out?
Some have 2, one for the power and one for switches on the door. If the one on the door is not working, the steps will not operate. Good luck. There is a troubleshooting pdf document you can download HERE that may be of help to you.
Why are the steps on my RV not extending?
RV steps will not extend. The RV steps should fully extend when the door is opened or the extend button is held. but if the ignition is on then the override switch may be preventing them from extending for safety. Another reason your RV steps will not extend is that the battery power may not be reaching the motor or control board.
How to keep electric steps from coming out?
You do need to keep the hinges lubed and clean…I do it every month and use a dry spray lube. Anytime you work on the step, STAY AWAY FROM IT’S PATH OF TRAVEL…It will hurt you badly! …You do need to keep the hinges lubed and clean…I do it every month and use a dry spray lube…
What to do when your RV step is not moving?
RV Steps Making Noise But Not Moving Doing a careful visual inspection is the first thing to do when looking for a solution if your RV steps make noise but aren’t moving. Check the underside of the steps and look for any debris that might be caught in between the linkage.
Do you need to replace automatic steps on RV?
Automatic steps on an RV certainly add convenience and even a cool factor. But automatic RV steps have many moving parts and take a lot of abuse from us constantly stepping on them. Those moving parts eventually wear out and need replacing. I’ll show you how easy it is to save money and repair your broken automatic RV steps yourself.
If so your step will not operate. You might also have a bad magnetic switch in your door, if so again your step won’t operate. Let us know what you find. Most steps run off the engine battery so you can turn off the house and still get in and out of the motor home. You might want to check fuses for the steps.
RV Steps Making Noise But Not Moving Doing a careful visual inspection is the first thing to do when looking for a solution if your RV steps make noise but aren’t moving. Check the underside of the steps and look for any debris that might be caught in between the linkage.
On Automatic RV steps, the magnetic switch is the one that makes your steps extend when the door opens and ensures that your RV steps retract when the door closes. There is a magnetic switch found on the sides of the door and the door frame. These should be aligned perfectly for the electric steps to automatically retract.
Automatic steps on an RV certainly add convenience and even a cool factor. But automatic RV steps have many moving parts and take a lot of abuse from us constantly stepping on them. Those moving parts eventually wear out and need replacing. I’ll show you how easy it is to save money and repair your broken automatic RV steps yourself.
What to do if your steps are not working?
Do not forget to check for faulty parts or bad connections to the door switch sensor and the on/off switch to the steps. If you still cannot determine what the problem is then contact the step manufacturer and/or Jayco for help. If that fails to bring results, then you will have to take the RV to a competent RV repair facility. Hope that helps.
What to do if your steps are on an automatic system?
We don’t know if your steps are on a manual system or an automatic electrical system, so here are some suggestions for each: If you have a manual step system then the repair might be simple. Start by lubricating all the moving parts, and visually inspect all the parts. Look for obstructions and bent or broken parts.
1 Disconnect the main connector to step and controller unit 2 Remove the bolts securing the controller board (leave wires connected) 3 Replace the controller board with the new one and secure it with the bolts 4 Move each wire from the old controller to the new controller 5 Reconnect the main plug to the step 6 Verify proper step operation
What to do if your step system is not working?
If you have a manual step system then the repair might be simple. Start by lubricating all the moving parts, and visually inspect all the parts. Look for obstructions and bent or broken parts. If there is an obstruction then remove it. If there is a bent part, straighten it or replace it. A broken part may be difficult to replace.
We don’t know if your steps are on a manual system or an automatic electrical system, so here are some suggestions for each: If you have a manual step system then the repair might be simple. Start by lubricating all the moving parts, and visually inspect all the parts. Look for obstructions and bent or broken parts.
What to do if your steps have a bad motor?
If you get a motor with the wrong number of teeth, don’t panic. You can usually move the correct gears from the old motor to the new one. The control unit for the steps is a solid-state unit that has no moving parts and very seldom fails. Almost all erratic step behavior is caused by a bad motor.
Why are the gears on my electric steps not working?
It could be that the gears are stripped on the motor (they’re plastic), so it only extends to where the bad spot is on the gears. If you can hear the motor spinning when the steps are stopped, that’s likely the problem. You could still have a bad controller, but in my experience, that’s the least likely possibility.
Some have 2, one for the power and one for switches on the door. If the one on the door is not working, the steps will not operate. Good luck. There is a troubleshooting pdf document you can download HERE that may be of help to you.
First verify that the magnet in the door and door frame switch are aligned. They should line up when the door is closed. Then check if power is getting to the step motor. Disconnect the power cable from the motor. Then use a multi-meter to check for a DC voltage reading of around 12 volts when the door switch is activated.
It could be that the gears are stripped on the motor (they’re plastic), so it only extends to where the bad spot is on the gears. If you can hear the motor spinning when the steps are stopped, that’s likely the problem. You could still have a bad controller, but in my experience, that’s the least likely possibility.
How does electric step work on Rapido motorhome?
(My Rapido motorhome has a Thule electric slide-out step with two separate operating switches, one extending the step and the other retracting it. If it has been extended, the step will automatically retract when the vehicle’s engine is started.
Where does the step switch on a motorhome come from?
Standard step diagrams issued by Omnistep show the manual step switch supplied from the habitation battery, while a supply conrolled by the ignition switch is used to supply the relay and motor for the auto retract function. To cater for the stalling current both supplies are normally fused at 25A.
How big is the electric step on a motor home?
The switch inside the door, the up and and down are side by side, each switch is about half inch wide and inch and a half high. There is a diagram on the surface of each switch not unlike the switch on your wiring diagram. For what it is worth, the caravan place took the covering off the switch and got his nod of approval.
Why is the step motor on my RV not working?
If a positive or negative voltage is present when the door switch is activated, then the step motor is getting power, but not working. The step motor is likely bad and needs to be replaced. WARNING: Be careful where you place your hands and arms when reconnecting plugs on the step.
Why does my electric motorhome step not retract?
Thanks Since you noted that your powered electric motorhome step does have power it may not be a fuse that is giving you the trouble. Depending on the system you have there could be a fuse in the main power panel or in the wiring between the battery and step controller or motor.
Is the electric step on my motor home working?
Four wires, one black, one brown, and two blue. There is a name and number in there if it means anything. “vender” 1052 OD. The remote control battery is OK, not bad for nearly 5 years. When I press the remote control I hear from the step as if it is trying to work. When I press the buttons on the wall I hear nothing. Thanks for the patience. No.
When do the steps retract on a Class A motorhome?
If the switch is on, the step should stay out. NOTE: If you have Class A or Class C motorhome, the steps will typically retract when the engine is running (regardless of the override switch position). The rest of the switching for the step occurs in the step controller board.
How to download a Fleetwood RV owner’s manual?
Download a Manual 202120202019201820172016201520142013201220112010200920082007200620052004200320022001200019991998199719961995199419931992199119901989198819871986198519841983198219811980197919781977197619751974 Loading… Unable to find document
If the switch is on, the step should stay out. NOTE: If you have Class A or Class C motorhome, the steps will typically retract when the engine is running (regardless of the override switch position). The rest of the switching for the step occurs in the step controller board.
